Olson-technology OT-1000-HH Rev.X2 Manual de usuario

Model OT-1000-HH 1GHz SuperMod Optical Transmitter, DWDM ADVANCED OPERATING MANUAL The features mentioned in this Advanced OT-1000-HH Manu

025-010573 Rev. X2 - 10 - www.olsontech.com Switching Optical Output Power On/Off The OT-1000-HH allows putting the transmitter into standby mode.

025-010573 Rev. X2 - 11 - www.olsontech.com Changing the ITU Frequency The picture below shows, how to change the ITU frequency (optical wavelengt

025-010573 Rev. X2 - 12 - www.olsontech.com Selecting the AGC Mode The transmitter can be operated in AGC-Off (manual) as well as in AGC-On (autom

025-010573 Rev. X2 - 13 - www.olsontech.com Setting the RF Gain (AGC-Off Mode only) The picture below shows how to adjust the RF gain, in order to

025-010573 Rev. X2 - 14 - www.olsontech.com Setting the RF Mode There are three different RF modes as shown in the picture below: Figure 12 — Se

025-010573 Rev. X2 - 15 - www.olsontech.com Setting the RF Gain Slope The OT-1000-HH enables the change the slope of the RF gain of its internal R

025-010573 Rev. X2 - 16 - www.olsontech.com Setting the OMI of the Pilot Tone The OT-1000-HH provides a pilot tone that can be used with return pa

025-010573 Rev. X2 - 17 - www.olsontech.com Setting the Pilot Tone Frequency The frequency of the pilot tone of the OT-1000-HH can be changed, if

025-010573 Rev. X2 - 18 - www.olsontech.com Setting OMItotrms (AGC-On Mode only) The picture below shows, how to adjust the total root-mean-square

025-010573 Rev. X2 - 19 - www.olsontech.com Line Coding The transmitter is capable to transmit a line code for easy link identification and verif

025-010573 Rev. X2 - 2 - www.olsontech.com TABLE OF CONTENTS CONTROLLING THE OT-1000-HH VIA NEC ...

025-010573 Rev. X2 - 20 - www.olsontech.com Setting the RF Gain Limit (AGC-On Mode only) The picture below shows how to adjust the maximum RF ga

025-010573 Rev. X2 - 21 - www.olsontech.com LIMITS MENUS The two limits menus of the OT-1000-HH determine, what deviations from the nominal values

025-010573 Rev. X2 - 22 - www.olsontech.com EVENT MASK MENU The OT-1000-HH allows setting an I/O port mask, if a NEC with application software 1.9

025-010573 Rev. X2 - 23 - www.olsontech.com PROPERTIES MENU The properties menu of the OT-1000-HH gives on overview of the appearance of the trans

025-010573 Rev. X2 - 24 - www.olsontech.com SOFTWARE UPDATE The devices update menu allows uploading new application software to all devices, whic

025-010573 Rev. X2 - 3 - www.olsontech.com PROPERTIES MENU...

025-010573 Rev. X2 - 4 - www.olsontech.com CONTROLLING THE OT-1000-HH VIA NEC The RS-485 interface is used to manage the OT-1000-HH, such as read

025-010573 Rev. X2 - 5 - www.olsontech.com For details on operating the OT-1000-HH via a NEC, please refer to the NEC operating manual. STATUS ME

025-010573 Rev. X2 - 6 - www.olsontech.com PARAMETER MENU The parameters menu displays the most important operation values of the transmitter: 

025-010573 Rev. X2 - 7 - www.olsontech.com VOLTAGES MENU The voltages menu displays all internal supply voltages like shown below: Figure 4 — Vol

025-010573 Rev. X2 - 8 - www.olsontech.com SETTINGS MENU This menu allows changing some basic transmitter adjustments. Figure 5 — Settings Menu

025-010573 Rev. X2 - 9 - www.olsontech.com Adjusting the Optical Output Power The picture below shows, how to change the optical output power. Fi